Kmx 8x8 midi patchbay3/22/2023 ![]() ![]() If you have a lot of MIDI devices, you will find the UM-880 to be an integral part of your studio or stage rack, or both. The UM-880 can also act as a Stand-alone MIDI patcher with 8 memory locations where you can store patch settings.įast and stable MIDI data transmission realized by FPT (Fast Processing Technology of MIDI transmission)Ĩ sets of input/out connections can be stored into memory The hardware MIDI patcher makes use of HDMR (Hardware Direct MIDI Routing) technology to ensure low-latency. MIDI can be routed directly, simply by pressing the panel buttons and there are none of the complicated settings that are all too common on software patchers. The UM-880 features hardware MIDI patcher functionality. You can also use up to four UM-880 units simultaneously, expanding your system to 512 channels. The UM-880 is hot-swappable, so you can plug and unplug the UM-880 even while your computer is on. It's easy to connect to your computerÖsimply connect a USB cable and you're done. With eight sets of MIDI inputs and outputs, the UM-880 lets you simultaneously control up to 128 channels. The vast majority of functions are available through either one or two button commands on the front panel. The UM-880 is the most powerful, easy to use MIDI interface/MIDI patcher available. If you send data out MIDI channel 1, over one cable, and assign that input to multiple outputs, it's logical that all instruments will play all MIDI channels sent, unless you set the individual instruments to only receive on one specific MIDI channel (or send out sysex to turn off channels).8 IN/ 8 OUT USB MIDI Interface with hardware MIDI patcher The MIDI ports you are using are the ports on the C8. All it will do is re-assign it's MIDI inputs to it's MIDI outputs. The KMX is a MIDI patchbay, not a MIDI interface. ![]() You can assign the name "KMX" to either of the two available output ports of the C8, but it only makes it recognizable for selection, it really does nothing functional in this case. MIDI studio only assigns recognizable names to the ports connected to the computer. It's connected to the C8, which is connected to the computer. The KMX isn't even connected to the computer. It does it just doesn't have a prenamed assignment for the KMX. You would think PT would have a way to route this in Midi Studio Setup. What computer MIDI interface were you using with other software? Was it the same setup as you are trying to use here? Out the C8 ports? I'm thinking no, as it just isn't physically possible. If I am daisy chaing, why did it work with other software? I actually need this many channels and instruments for orchestartion in case you are wondering. If i say midi track 4 is trans on all and rec Roland JV ch 13 and midi ch 5 is trans on all and rec Proteus 1 ch 13, track 4 and 5 should not be "sharing" the same channel. ![]() The difference is no matter how many external modules I use and assign them on the rec ch in PT, they all play at the same time if they are using the same channel, not individually. Same as in PT where you assign midi rec channel. Port 1 goes to Roland mod, Port 2 goes to Yamaha mod, etc. In other software it's like assigning ports. If I'm transmitting on "all" and rec on any particular module ch, only that module should play like virtual instruments do. Yet in PT I'm using the receive in the mix window as the receiving module. My problem here is that when I use the same receive channel on each module, they both play their preset assigned to that channel. I've done this before with other systems, platforms, software, etc. Ensoniq KMX-8 8x8 Programmable MIDI Patch BayFull featured 8-input x 8-output MIDI patching. When I'm routing midi, I'm going out of my controller in to the C8, out of the C8 in to a midi patchbay, from the PB to sound modules. I'm using PT 6.9 with the 002 and a Command 8. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |